| Corin |
Yes, I believe it only shows one entry at a time, not a whole list.
When it's playing, and you don't see the song information, try pushing the "tuning" knob. For my Bose radio, this is how you make the song info come up both for the Ipod and for Sat. You have to do this EACH TIME you start the car.
That, of course, is for my Bose radio. I assume that the non-bose has a similar feature. |
|
|
| rixmo |
| It only shows one playlist at a time as you scroll through. To toggle between artist name and song title, I hit the right radio knob. It's the one that shows balance, treble, and bass settings during normal radio use. Keep in mind, I have an '05 so this might not be the same for you. |
|
|
| jerseyparts |
Sorry bout that, I was jammed at the office.
Yes you will only see one playlist listing at a time, you will not see all of them, you can scroll through them by using the Tuning knob though.
As far as display, these guys are correct, you should just have to push your tuning button in once.
You can also keep pushing this button, till you get to display, and change the propeties from there as well.
B |
|
|
| gfb107 |
| On the 2007, you change the display settings using the DISP button. While listening to your iPod, press the DISP button. It'll cycle from none to NAME to TITLE to NAME & TITLE then back to none. |
|
|
| katys |
Thanks so much everyone! I hit the DISP button, and it gave the the options of artist/song, song, or just artist.
I was almost ready to pack it up and ship it back! How sweet would it be if it would interface just like the iPod?!? (Showing all the playlists/artists/or albums.)
Thanks again! |
|
|
| gem_tim |
got a couple of questions. First, my hats off to all of the guys and gals who have put such great info out here. After reading this I have the courage to attempt both the XM-Sat install and IPOD connection. I have an 05 MO with the 6-cd Bose changer with the "SAT" button on it. My questions are what parts will I need to do this? Which box comes off of the Harness first, the Radio tuner or the Box for the IPOD? I would like the IPOD to be stored in either my Glove Box or my Center Console.
Thanks,
Tim |
|
|
| rixmo |
| Work with Yournissanparts.com for the correct part numbers. As for hookup, you connect a new harness to your sat plug under the rear seat. Then you hook the magic IPOD box up to that. On the back of the magic box, you attach both the new IPOD cable and a new sat harness. I don't think you'll be able to get IPOD and satalite and still be able to reach your glovebox. The reason is that the satalite is installed in the rear of the car and there isn't enough cable to reach from there to the front glove box. You'll need three cables and one magic box for this install, but I don't know all the part numbers. |
|
|
| gnotti211 |
| It might not be true, but i heard that if the iPod is plugged in, you will not be able to use SAT...you would need to unplug the iPod (which could be in the trunk) to use SAT...which would be a inconvenience for me atleast |
|
|
| Corin |
quote:
Originally posted by gnotti211
It might not be true, but i heard that if the iPod is plugged in, you will not be able to use SAT...you would need to unplug the iPod (which could be in the trunk) to use SAT...which would be a inconvenience for me atleast
That is correct. With my setup the Ipod is in the center console, so I can unplug it there and that puts me right back to SAT. Plug the ipod in, and it disables SAT and plays ipod where I left off.
If you want to switch back and forth, make sure you have the ipod somewhere that you can reach easily. The stock cables will easily reach to the center console (while crushing your fingers to route the cable into there) but it will not reach the glove compartment. |
|
|
| jerseyparts |
Well I have good news for all of you folks who have not ordered the ipod adapter, because you did not want to run wires from the back to front.
After lots of R&D we have come up with a cable, that connects at the Back of Radio, and allows the Ipod adapter to be installed under the front dash, AND you will still be bale to install the SAT in the beack of the vehicle.
We will be posting this new setup on the site in the next few days.
This will solve alot of problems. |
|
|
| gem_tim |
| Thanks Jerseyparts. So let me make sure I am clear on what you are saying. This new cable will let me mount the IPOD adapter in the front dash incependent of the cable for the SAT in the rear or will the cable that runs to the rear for the SAT be plugged into the IPOD adapter that is now mounted in the front in the new design? |
|
|
| jerseyparts |
| Yes, with this new setup you will require 2 harnesses, but they are small harnesses that go behind the radio, your Sat harness still works in the rear, but your ipod is behind the dash, with the cable coming out of the dash to your ipod. |
|
|
| gem_tim |
Oh so no box needed for the IPOD, just a direct cable from the back of the radio to the IPOD, that is great. Please let us know when this is ready for prime-time.
Thanks so much |
|
|
| jerseyparts |
| No, the box is still needed, it just is mounted under the dash now, instead of in the rear. |
|
|
| deeto |
quote:
Originally posted by jerseyparts
Well I have good news for all of you folks who have not ordered the ipod adapter, because you did not want to run wires from the back to front.
After lots of R&D we have come up with a cable, that connects at the Back of Radio, and allows the Ipod adapter to be installed under the front dash, AND you will still be bale to install the SAT in the beack of the vehicle.
We will be posting this new setup on the site in the next few days.
This will solve alot of problems.
Wait, where does the iPod itself get placed? Under the dash? |
|
|
| jerseyparts |
The Ipod can be put anywhere in the front you want.
In the Center Console, in the glove box, in a Ipod Holder.... |
|
|
| gnotti211 |
Jerseyparts -
If i already have SAT installed, will i still be able to do this? Also, assuming that i can do this, willi need to disconnect the iPod everytime i want to switch to SAT? |
|
|
| gfb107 |
quote:
Originally posted by jerseyparts
The 04 Quest uses the VR000, that is the only difference.
For my birthday, my wife bought me the ipodwosat kit for my 04 Quest (I drive it 'cause I'm a stay at home dad). It has the VS000 and VR000 parts.
I got the dash taken apart and radio removed, but I can't find a place to connect the VS000 harness to the radio. Neither connector matches the only available port, nor do they match any of the existing cables. Is the 04 Quest pre-wired for SAT? Where would the pre-wired harness be so I can connect it to the VS000 harness? |
|
|
| zevo |
| What parts would this Jersey parts set-up require. I have an 07 Murano S without Bose or satellite. I'm not interested in satellite radio, but want the ipod. Am I correct that I still would need the vr0002 magic box thing and the part from jersey parts to run only the ipod. |
|
|
| jerseyparts |
Ok, let me see if I can answer some questions, the New item is ONLY a harness, you still need the "Magic Box" to work this, you just do not need all the other harnesses.
This unit will allow you to continue using the Sat receiver in the Back with an ADDITIONAL Harness, but this all hooks up under the dash.
GFB107, I sent you a PM I need your email address to send you the info you need.
The 07 Would need either the New harness setup, or the Old Harness setup. either one will work it just depends on where you want the ipod to be hooked up, in the front by the dash, or through the rear to the center console.
Yes you would still need to UNDOCK the Ipod for Satellite to work with any of these connections.
Brian
www.NissanIpod.com |
|
|
| gnotti211 |
Jersey parts -
I am going to purchase an iPod hook up for under the dash...what exact parts am i going to need to buy to get everything i'll need in one shot?
is there a link to each the ipod connector itself and the magic box? That would be a huge help if you could post it...i have a 07 murano with satellite
Thank you |
|
|
| gnotti211 |
| Sorry if im being a pain in the you know what...but i'm assuming that includes the "magic box" that other members were talking about?? |
|
|
| deeto |
yes, it does come with the box. It has everything you need.
to be honest I thought the price would be coming down, but I guess not.
$250 is just way too much. You guys are gouging.
Sorry Brian. I'm sure its a great product, but its not worth two-hundred and fiddy bucks. |
|
|
| Corin |
quote:
Originally posted by deeto
yes, it does come with the box. It has everything you need.
to be honest I thought the price would be coming down, but I guess not.
$250 is just way too much. You guys are gouging.
Sorry Brian. I'm sure its a great product, but its not worth two-hundred and fiddy bucks.
I agree, $250 is too much. I bought one, and I really like it, but I still say I paid for more than it's really worth.
On the other hand, it does seem like people are buying a LOT of these, so supply and demand say that it IS worth the price. At least for now. |
|
|
| kitesurf |
Has anyone in this group removed the head unit? I want to buy the new harness that connects to the rear of the head unit but am not certain on the steps to remove the stereo.
$250 too much? Personal call. It is a good price for me since I will not have to mp3 my 60G worth of music and sort them to folders to burn them to discs... |
|
|
| gnotti211 |
kitesurf,
Here is the link to the thread:
Radio Head Removal Instructions
Jerseyparts,
One final question, i promise....how much extra slack will i have with the cord coming out of the head unit..will there be enough for me to hold it up to eye level and adjust or am i going to have to bend over to read it due to not enough slack..? |
|
|
| deeto |
agreed... its a personal call of course.
some people have enough disposable income to absorb this cost without blinking an eye.
some don't.
although I would put myself in the first category, in my mind it still doesn't negate the fact that I could purchase a new laptop computer for the same price.
I understand this is a niche market and jerseyparts or whoever makes this iPod unit doesn't have the same access to low cost technology hardware as the big computer makers.
but still, at the end of the day you're paying $250 for something that probably costs $30 to $40 in raw materials to make. Given these margins - and the demand as you mentioned Corin - I'm sure the R&D costs have been covered by now.
Which brings me back to my original point. They're gouging.
Regardless, I'm sure its a great product and I wouldn't mind having one. I'm getting mighty tired of my FM transmitter setup. But I think I'll wait for someone in Korea or China to copy the design and sell it on eBay for $75 bucks. Its bound to happen sooner or later.
Sorry if I'm coming off like a cheap douche-bag and beating a dead horse. I don't mind paying a little extra for luxury items. I do mind when companies take advantage of people. Especially good people like us on this forum.
Now if we could get a group buy together maybe that would reduce the cost to an acceptable level. Has this been discussed before? |
|
|
| kitesurf |
| gnotti211 - thank you for the link. I plan on running the ipod to the glove box. I think Brian has stated in the past that the ipod will not be able to be read after you plug it into the adapter but he can verify. |
|
|
| dylanursula |
quote:
Originally posted by deeto
agreed... its a personal call of course.
some people have enough disposable income to absorb this cost without blinking an eye.
some don't.
although I would put myself in the first category, in my mind it still doesn't negate the fact that I could purchase a new laptop computer for the same price.
I understand this is a niche market and jerseyparts or whoever makes this iPod unit doesn't have the same access to low cost technology hardware as the big computer makers.
but still, at the end of the day you're paying $250 for something that probably costs $30 to $40 in raw materials to make. Given these margins - and the demand as you mentioned Corin - I'm sure the R&D costs have been covered by now.
Which brings me back to my original point. They're gouging.
Regardless, I'm sure its a great product and I wouldn't mind having one. I'm getting mighty tired of my FM transmitter setup. But I think I'll wait for someone in Korea or China to copy the design and sell it on eBay for $75 bucks. Its bound to happen sooner or later.
Sorry if I'm coming off like a cheap douche-bag and beating a dead horse. I don't mind paying a little extra for luxury items. I do mind when companies take advantage of people. Especially good people like us on this forum.
Now if we could get a group buy together maybe that would reduce the cost to an acceptable level. Has this been discussed before?
Deeto.... I have to agree with you. I thought I would buy this but at $250 even though its not a huge amount to me; its still FAR TOO HIGH for what it is. If it were $150 then thats still a tad high but ok-ish for something that probably costs $50 to make. |
|
|
| GripperDon |
Parts reall a bunch of them plugs, Wire, Spades, Tape, solder
Fixtures, Wire layout boards, Crimpers, Sodering irons etc.
Drawings, Parts lists, Sourcing, Ordering, receiving, Inventory,
Assembly stations, Instructions shets and drawings
Labor for bothe direct workers and supervision staff, Rent, Insurance, Lighting, Water, Taxes, Accounting, Customer interface labor. Recovery for All experimentation and try outs, use of vehicles to work on. Warranty costs.
All divided over a smalish number of units.
I have done this this is not some place in the far east that pays workers 25 cents an hour, This is Americian brain power built in America and paying the American Costs. Price High, I don't think so. Can a person afford to buy it. Well the Ipod and Sat radio sure are not cheap and parts from Nissan are not cheap if you can afford them and not this Thats your call but I don't feel cormfortable to hear them called gougers,That's a td harsh IMHO. There is a lot more than meets the eye to make something that no body else has done. |
|
|
| deeto |
fair enough.
I'm not out to tarnish Brian's rep. Like I said above, I'm sure the products are great and perform as advertised. If I didn't think it was over-priced I would own one, no question about it.
Grip I agree with some things you said. But be careful about making assumptions. We don't know where these parts are made, who makes them, or more importantly - the costs associated with those processes.
Based on statements from the website, the manufacturing of the wiring harnesses is outsourced. It would seem plausible that other items contained in this product are outsourced as well. Which is why I don't believe the actual cost of them exceeds ~$40.
So that leaves ~$210 for operating expenses and profit, per unit. If this was the only product sold by the company, those numbers would be easier to swallow.
In my opinion, the truth of the matter here is that Brian knows his product is unique. He's taking advantage of that by inflating the price significantly. Honestly, I don't blame him. There are lots of folks willing to pay that price for his product. I'm just not one of them.
Sooner or later (my guess is sooner) someone who understands EE will copy his design and sell it for much less. It may be an inferior quality product or not come with the same customer service, but if its $150 cheaper does that really matter?
I bet most folks would say no.
(btw I am not saying its OK for someone to copy his design, just that its going to happen)
anyway, I really hate to keep posting about this. It makes me feel cheap and dirty. I've previously spoken to Brian on the phone and he's a super-nice guy, very knowledgeable and very helpful. |
|
|
| gnotti211 |
| I'm up for a group buy...that's the only way i would probably buy it cause i don't want to pay the whole $250 but would pay for a discounted price... |
|
|
| jerseyparts |
quote:
Originally posted by deeto
fair enough.
I'm not out to tarnish Brian's rep. Like I said above, I'm sure the products are great and perform as advertised. If I didn't think it was over-priced I would own one, no question about it.
Grip I agree with some things you said. But be careful about making assumptions. We don't know where these parts are made, who makes them, or more importantly - the costs associated with those processes.
Based on statements from the website, the manufacturing of the wiring harnesses is outsourced. It would seem plausible that other items contained in this product are outsourced as well. Which is why I don't believe the actual cost of them exceeds ~$40.
So that leaves ~$210 for operating expenses and profit, per unit. If this was the only product sold by the company, those numbers would be easier to swallow.
In my opinion, the truth of the matter here is that Brian knows his product is unique. He's taking advantage of that by inflating the price significantly. Honestly, I don't blame him. There are lots of folks willing to pay that price for his product. I'm just not one of them.
Sooner or later (my guess is sooner) someone who understands EE will copy his design and sell it for much less. It may be an inferior quality product or not come with the same customer service, but if its $150 cheaper does that really matter?
I bet most folks would say no.
(btw I am not saying its OK for someone to copy his design, just that its going to happen)
anyway, I really hate to keep posting about this. It makes me feel cheap and dirty. I've previously spoken to Brian on the phone and he's a super-nice guy, very knowledgeable and very helpful.
Ok lets clear something up right off the Bat,
I do not make the Ipod Adapters, these are a GENUINE Nissan Part that I sell at a Discount. I do not manufacture them, I do not have any say in the software that runs in them, I do not own any of the rights to produce them.
I am a Nissan Dealer that sells these units to you folks, the ONLY thing I am in control of is the Harnesses, these I contract out to be created. I make EXACTLY $7.00 on the Harnesses.
I understand your Point about the Pricing, and if you feel I am gouging, call your Local Nissan Dealership and ask them what an Ipod Adapter kit for the Nissan Titan Runs... You will find they are getting $300.00 and more, and they do not have the custom cables, they have the stock cables which will not allow you move the ipod further than the rear seat of the Murano.
Nissan owns the Rights to the Plug Design, it is why the aftermarket does not have much in the way of Adapters for the Nissan Vehicles, because Nissan demands a High Price for duplication of their copyright.
The harnesses I have Made are all Originally Genuine Nissan Harnesses, I send them out with specific instructions on what I need altered or added. I can not afford to pay Nissan to create these harnesses on my own, I need to use their Propietary Cables, and pay their designated cost for these Harnesses BEFORE I can even send them out to be customized.
I would really like to see what happens when you call the Nissan Dealer, and ask for an Ipod kit for a Murano, You know as well as I do, they will tell you it does not exist.
I spent my time and my money to develop only the Harnesses that allow you to install this adapter in your Muranos in Convenient places, if you feel that I am gouging, then please do not purchase from me, if you can not buy from me without thinking I am ripping you off, then I do not deserve the sale.
I think anyone who has purchased this kit from me, has not only recieved the Kit, but also recieved customized service to any of their needs, I try to do everything possible to ensure that they are Happy with their purchases.
Again, if you think I am gouging, call your Local Nissan Dealer, and just ask them what they would sell the 999U7-VR002 adapter to you for, you will be pleasantly surprised when they tell you they will charge you more for that box than I would charge you for the whole kit with customized harnesses.
Thank you for all the People who stood up in my defense, I appreciate knowing that there are people out there who understand what I am trying to do, Yes I am trying to Make Money, but I also trying to give you something that Nissan never would have spent the time to do for you.
Brian |
|
|
| gnotti211 |
Brian -
I appreciate you clearing everything up..there was definitely a misunderstanding. You can count on me ordering one of these in the near future |
|
|
| jerseyparts |
quote:
Originally posted by jerseyparts
Ok lets clear something up right off the Bat,
I do not make the Ipod Adapters, these are a GENUINE Nissan Part that I sell at a Discount. I do not manufacture them, I do not have any say in the software that runs in them, I do not own any of the rights to produce them.
I am a Nissan Dealer that sells these units to you folks, the ONLY thing I am in control of is the Harnesses, these I contract out to be created. I make EXACTLY $7.00 on the Harnesses.
I understand your Point about the Pricing, and if you feel I am gouging, call your Local Nissan Dealership and ask them what an Ipod Adapter kit for the Nissan Titan Runs... You will find they are getting $300.00 and more, and they do not have the custom cables, they have the stock cables which will not allow you move the ipod further than the rear seat of the Murano.
Nissan owns the Rights to the Plug Design, it is why the aftermarket does not have much in the way of Adapters for the Nissan Vehicles, because Nissan demands a High Price for duplication of their copyright.
The harnesses I have Made are all Originally Genuine Nissan Harnesses, I send them out with specific instructions on what I need altered or added. I can not afford to pay Nissan to create these harnesses on my own, I need to use their Propietary Cables, and pay their designated cost for these Harnesses BEFORE I can even send them out to be customized.
I would really like to see what happens when you call the Nissan Dealer, and ask for an Ipod kit for a Murano, You know as well as I do, they will tell you it does not exist.
I spent my time and my money to develop only the Harnesses that allow you to install this adapter in your Muranos in Convenient places, if you feel that I am gouging, then please do not purchase from me, if you can not buy from me without thinking I am ripping you off, then I do not deserve the sale.
I think anyone who has purchased this kit from me, has not only recieved the Kit, but also recieved customized service to any of their needs, I try to do everything possible to ensure that they are Happy with their purchases.
Again, if you think I am gouging, call your Local Nissan Dealer, and just ask them what they would sell the 999U7-VR002 adapter to you for, you will be pleasantly surprised when they tell you they will charge you more for that box than I would charge you for the whole kit with customized harnesses.
Thank you for all the People who stood up in my defense, I appreciate knowing that there are people out there who understand what I am trying to do, Yes I am trying to Make Money, but I also trying to give you something that Nissan never would have spent the time to do for you.
DEETO: Please do not misunderstand this post, I am not out to scold you or instigate you, I just wanted the facts out and some of my opinions thown in ther as well, I understand exactly what you are saying, and I agree with you 100%, I hate it when I see Dealers selling parts at 20 - 50% over list, that in my opinion is gouging, and lots of dealers do it. I just wanted the point out that I do not manufacturer the Adapters, I onyl use the Genuine Nissan Ipod which is a VERY expensive part and that cost is set by Nissan, not by myself.
Brian
|
|
|
| drumbear |
I don't normally post much, but I had to comment on this discussion.
I had ordered the rear Ipod adapter harness with the extended length ( since I want the Ipod up front with me). The announcement of the new front adapter hit after I had made my order. Brian called me to tell me that the adapater was in but that this new adapter was available. He could fill the order with the original adapter I ordered or he could send the new adapater and charge me $25 less.
Now, I would really prefer the new adapter since I have heard stories of the difficulties in running the cables through the carpeting, but I figured that I had already ordered it so it was a done deal. Not only did he offer to send me the adapater that, in my opinion will be in much higher demand, he is charging less for it.
That fact alone (not to mention the personal service) tells me that he is NOT "inflating the price significantly" and that the costs are NOT based on how much people will spend but instead on his own costs.
Just my $.02 |
|
|
| jerseyparts |
I don't believe Deeto was attacking me personally, I think he was just ill-informed..
I don't think anyone on here would question my service, I try to be as up front and personal as I can.
I appreciate the encouraging words,
as you all know, my business is built on word of mouth and you guys out there are the best!
With that said, I am waiting to see some reviews of the New Harness, some of you guys should have them in by now and I am wondering how you like it???
Brian |
|
|
| Corin |
Agreed, I don't think ANYONE is questioning Brian's business practices. Rather, questioning whether the unit itself is really worth the price. It's a common discussion with many products out there.
Is Mobil1 oil worth the inflated price over regular oil? Is an ipod worth the inflated price over any other mp3 player? Is paying for supreme Chevron worth the inflated price over Arco low grade? They're all value judgments, and each person has to answer each of those for themselves.
The Nissan Ipod adapter is expensive. Whether or not it's TOO expensive depends on the person wanting to buy it. I think the "attacks" were directed more at the manufacturer of the product rather than at Brian as a distribution channel. The price gouging (if any) is being done by the manufacturer, not (necessarily) by the individual dealerships selling the unit. |
|
|
| drumbear |
I finally had time to install the new up-front harness.
Let me start off saying that I love the adapter.
Installation:
The installation was a lot harder that I anticipated. While, you don't have the issues with pulling cable through the carpet, you have to remove the radio and access the connectors which are very very difficult to remove.
In addition, I didn't see any instructions that referenced the Murano radio (I don't know if Brian has those are not). I figured out by trial and error which connectors go where and after some sweat and cursing, got the adapter zip tied within the dash with the enclosed sticky padding on a cross member. I had the cable that goes to the IPOD sticking out from under the dash originally but now I ran it into the glove compartment with little trouble.
The kit includes a rubber grommet for running the cable through any plastic part but I haven't used it yet (keeping my options open). Overall on the harness, it is much harder to install in my opinion, but gives you much much more control on where the ipod is located and can easily but put where you can quickly grab the Ipod to keep it with you (be it the glove box, under radio tray, or any kind of mount).
Adapter Operation:
I LOVE how it works with the monitor in my mo. I can browse the artists, genres, and once you find the right radio button combinations, I can quickly randomize the selections. The steering wheel buttons also work more than I thought they would. The only one that doesn't work is the bottom selection button. The mode button and power button still works just fine. I just go to my C radio preference and press radio till it goes to the Ipod. I can then still go through all my radio channel presets on A or B, or listen to CD's, or the Ipod by using the mode button.
I also have the built in DVD system (center console) and although I can use the IPOD through its inputs (which go through a built in FM transmitter), there is a noticeable improvement of the sound when using this adapter (no to mention the wrecks I avoid not looking at a 2 inch screen).
I only have two main complaints:
One, that the selection button doesn't work on the steering wheel like it works on CD's (issue is with the adapter itself I think).
Two, that you can't show video on the screen (this is actually a problem not only with the adapter but the Ipod firmware itself doesn't yet allow video output to be controlled remotely).
Overall I would greatly recommend this adapter/harness combo. |
|
|
| SIM |
| My own experience of both devices proved that the Nissan Interface transports the iPod audio signal with an incredibly higher level of quality than the PAC. |
|
|
| Salden |
| Does anyone have a step-b-step procedure for doing the for installing this harness in the Mo? I was under the impression I'd be able to run the cable back into the center console's storage compartment but the cable that goes betweenthe iPod and "magic box" looks way to short to do it. I'd apreciate any tips before I embark on this installation voyage. |
|
|
| Salden |
Ok so I was able to install the 03 with no sat kit. Thanks jerseyparts! I managed to install the magic box between the head unit and the glovebox using the zip ties and securing it to the trangle shaped bracket that is just above the 12v accessory jack. I ran the wire through the center console and it comes out inside the center glove above its 12v accessory jack (but from the wall on the passenger side) I am able to strap the ipod in using the elastic band under the console lid. It's very nice!
The operation is very kludgy (I have the bose 6-disc in-dash w/navi). Does anyone have a writeup that is better than the included nissan instructions? Is there a way to have it display all the artist/track info on the screen rather than just at the bottom showing XM-02 or something? There's a picture earlier in this thread showing this but I think it's from a newer MO. Mine's an 03. Any help would be appreciated. |
|
|
| gem_tim |
Let me start off by saying all things being equal I would much rather prefer to install the adapter in the front(glove box, middle console etc.). However after reading some of the posts it appears to me that the front installation is much more difficult(I'm concerned about damaging the vent covers during removal) and thus I am considering a rear installation(although the IPOD would not be as convenient. Since I do have a Cargo protector it would be a pain to say lift it up to get into the side panels to get the ipod(not to mention if something were in the cargo area) but I would much rather do that if there is a signifcant chance in damaging the radio head or vent covers during their removal. For those of you who have done the front installation what do you think? Brian what do you think? It's killing me not to have this thing but I am on the fence about which way to go and I need you guys/gals to push me one way or the other
Thanks,
Tim |
|
|
| GripperDon |
They sell fairly cheaply plastic removal tool for the vents etc. The eliminate or certinally meii,ize the chance of damage to the plastic.
I installed items into the center glove box and ran wires along the consule to get there. The electrical outlets there are very handy. |
|
|
| biggun |
| I just ended up buying a 2" plastic putty knife from homedepot, which works just as good. |
|
|
| GripperDon |
| A nice taper and a very smooth finish. |
|
|
| jerseyparts |
The Front install is not really that bad, it involves lifting up on the trim around the info screen removing that trim (which you just pull it out after you lift it horizontal)
and then removing the plastic "L's" under the radio, this will give you access to the screws that hold the radio in.
Once you get to that point it is just a matter of plug and play.
The Harnesses are hard to get out of radio because the saftey tabs are hard to push down and pull out the cable, I suggest Harness Pliers which are available at most audio store, that have a small nub on one side of the plier teeth that will depress the button while you are pulling out.
the routing of the wires is much easier with the front kit because you have lots of avenues to go with it.
I suggest to most of my customers to go with the front route because it is a much cleaner install, there are no wires to hide under the carpet.
Just my opinion.
Brian |
|
|
| Aronsonstack |
quote:
Originally posted by SIM
This is the correct address for the previous message
It is a similar product. It shares the same advantages and drawbacks (no steering controls, cannot have both SAT radio and iPod connected at the same time).
So is the one on eBay a better buy at $179 versus $220 from nissanipod.com?
Can someone list the features on the one sold on nissanipod so we can compare? Below is the features for the one sold on eBay.
--------------------------------------------------------------------------------
CONNECTS iPOD
MAINTAINS FACTORY RADIO FUNCTIONS
DISPLAYS SONG TITLE AND ARTIST
WILL PLAY iPOD BY PLAYLIST SELECTABLE BY RADIO BUTTONS
WILL CHARGE iPOD WHILE CONNECTED IN THE VEHICLE
DEACTIVATES iPOD ROTARY CONTROL FOR SAFE DRIVING OPERATION
OFFERS SIMULTANEOUS OPERATION OF YOUR iPOD & AN AUX INPUT
COMES WITH iPOD ADAPTER INCLUDED, iPOD EXTENSION IS 6.5 FEET LONG, AND IS MADE WITH TRUE APPLE CONNECTORS
COMES WITH AUXILLARY CABLE FOR CONNECTING ANY RCA EQUIPPED DEVICE
You will be able to control your iPOD the following ways from your factory radio.
Random (Shuffle)
Scan (plays each track for few (10) seconds)
Browse (Playlist, Genre, Album & Artist) thru radio buttons
Repeat
Track Up/Down
Fast Track Search (x10)
Fast Forward/Fast Reverse Play
----------------------------------------------------------------------------------- |
|
|
| SIM |
I personnally would pick the Nissan OEM one for the small difference in pricing (for me) between both. I usually prefer to pay for a little more service and quality because my grandfather was often telling me with wisdom: "Boy, you can't afford to buy cheap." I always listened to him... :p
I often buy from eBay and sometimes find it hard to get support and/or warranty service. Sometimes... |
|
|
| pappabacon |
| I have been away from this post for alittle bit, but am confused. I used the Nissan Ipod kit, plugged into the back area, by the spare tire. I then bought the extension sold by jersyparts ( I think) and ran that under the carpet and into the center console. I will post some pics later, but don't understand the debate between front and rear install. Either tear apart your dash, or route the wire under the back seat carpet. Like I said Ill post pics later of my install, since I have it torn apart right now to install the tow harness kit. |
|
|
| jerseyparts |
PappaBacon,
There is a new Harness available which allows you to connect the Ipod at the Back of the Radio, it is a much cleaner install, but it is the same exact operation as the old style, you just don't have to hide 15 feet of wires anymore....
B |
|
|
| Aronsonstack |
quote:
Originally posted by SIM
I personnally would pick the Nissan OEM one for the small difference in pricing (for me) between both. I usually prefer to pay for a little more service and quality because my grandfather was often telling me with wisdom: "Boy, you can't afford to buy cheap." I always listened to him... :p
I often buy from eBay and sometimes find it hard to get support and/or warranty service. Sometimes...
Hey Sim, with the nissanipod version, is there an extra aux input too? |
|
|
| SIM |
| No Aux input on the Nissan interface. I can however vouch for the sound quality of the unit. IMHO, too many bells & whistles dilute the primary objective of a device. This is an iPod interface and I just need it to play my iPod with high quality digital rendering. The Nissan unit that I selected does however allow me to hook a satellite radio working with the iPod connected. To me this is something that increase the value of the unit since it enables all OEM options to be controlled from the head unit. |
|
|
| pappabacon |
| Oh, I had seen that, but I still think it was easier to run wires under the carpet versus tearing out vents and stuff like that, just my opinion. |
|
|
| Aronsonstack |
| BTW, what color is the wire of the cable connecting to the ipod? White or Black.. is there a choice? |
|
|
| pappabacon |
| I don't know if this picture makes sense. This is the box mounted upside down under the center console, with the out wire then running up into the console. I drilled a half in. hole to use the grommet included with the kit. I love it. |
|
|
| jerseyparts |
| The wire only comes in Black. |
|
|
| Agent_DESI |
quote:
Originally posted by gfb107
And finally the ipod kit installed in the space covered by that carpeted panel:
How easy is it to get the IPOD routed to the center console from here on? any drilling required?
I believe this type of installation can only be done in 07 MO without the extended harness? |
|
|
| Aronsonstack |
quote:
Originally posted by jerseyparts
The wire only comes in Black.
Are there step by step instructions provided for the complete FRONT INSTALL package? Maybe a link?
I've gotten the step by step intall instructions for the ebay version and it seems quite involved, such as disconnecting the negative battery, etc.
I'm wondering if it's virtually the same steps if I'm installing the Nissanipod version. |
|
|
| Aronsonstack |
| Another thing I"m curious about... Is the IPOD disabled automatically when car is in operation? |
|
|
| zevo |
| I want to buy an ipod connector for my wife's Murano. It is a 2007 w/ single cd non bose stereo that is not satellite enabled. She wants to be able to have it in her console. Would I be able to do this with the 999U7-VR002 and 999U7-VS000? Also, does anyone know if there are any better options coming for 2008, if so I would wait for that. |
|
|
| jerseyparts |
quote:
Originally posted by zevo
I want to buy an ipod connector for my wife's Murano. It is a 2007 w/ single cd non bose stereo that is not satellite enabled. She wants to be able to have it in her console. Would I be able to do this with the 999U7-VR002 and 999U7-VS000? Also, does anyone know if there are any better options coming for 2008, if so I would wait for that.
I do not believe that Nissan will be updating the Ipod Adapter in the Near future, because most cars are going to the new XM Nav Traffic system which is Navigation and Satellie Radio built into one.
If you wanted to use the above parts, and stretch them you could make the center console, BUT you would need to hide the wires from the cargo area to the console.
This is the reason we came out with the Front Harness install package, it attaches at the back of the radio, and gives you the ipod at the front of the vehicle, and allows alot more options on where to put the ipod.
Brian
www.NissanIpod.com |
|
|
| pappabacon |
| Jerseyparts, don't you guys also sell an extension for the rear? I could have sworn I bought it from you. |
|
|
| jerseyparts |
quote:
Originally posted by pappabacon
Jerseyparts, don't you guys also sell an extension for the rear? I could have sworn I bought it from you.
Yes, we can make extensions for the rear, they run about 69.99, but we order them as needed because of the new front install cable....
B |
|
|
| jerseyparts |
Has anyone tried the New i-Phone on the Ipod Adapters, I do not have one to test here, and I was wondering if it was working as usual, and if it still let someone answer the phone (Since it locks out the ipod)
Brian |
|
|
| kevin86 |
quote:
Originally posted by jerseyparts
Has anyone tried the New i-Phone on the Ipod Adapters, I do not have one to test here, and I was wondering if it was working as usual, and if it still let someone answer the phone (Since it locks out the ipod)
Brian
Can you please let me know if you get an answer to this. I have an iphone and the only thing holding me back from purchasing the ipod kit from you, is this question.
Thanks. |
|
|
| jerseyparts |
Actually after I posted this I got a phone call from someone with a iPhone and this is what he said:
When you plug in the iPhone, the phone asks you if you want to go into Airplane Mode, if you select NO, it will then work as a normal ipod, until the phone rings, then it will shut off the ipod and revert to a phone, IF you select YES to an the Airplane mode, it shuts down the phone functions and work ONLY as an Ipod, so always select NO and you will be good.
Brian |
|
|
| kevin86 |
quote:
Originally posted by jerseyparts
Actually after I posted this I got a phone call from someone with a iPhone and this is what he said:
When you plug in the iPhone, the phone asks you if you want to go into Airplane Mode, if you select NO, it will then work as a normal ipod, until the phone rings, then it will shut off the ipod and revert to a phone, IF you select YES to an the Airplane mode, it shuts down the phone functions and work ONLY as an Ipod, so always select NO and you will be good.
Brian
Great thanks. Last question, I have an 07 with Satellite radio. To install the kit do I have to unplug the satellite? |
|
|
| jerseyparts |
With the front install you are unplugging the Satellite AT the back of the radio, and you get a harness that plugs into the ipod adapter and back into that sat harness, so it will work just as before, except when you have the ipod plugged in.
Brian |
|
|
| GallifreyRebel |
Ok, just found this site this morning and have been scanning the board. What I have yet to see (or have missed) is the question pertaining to the iPod adapter for cars with SAT or without SAT. I just ordered the kit from yournissanparts.com and when I spoke with them they said I needed the with SAT version. From what I am reading on the nissanipod.com site it says the opposite.
I have a 2007 with NAV, the car is pre-wired for SAT but that is not installed. I ordered the SAT version of the kit, did I get the wrong thing, should I cancel the order and order the without SAT version? What's the difference, not that I plan on ever using a SAT option (who needs that if I have my iPod running! LOL) :)
Thanks for the help!
-=Steven=- |
|
|
| gem_tim |
| First off I would like to thank Everyone who posted info out here because it really helped me. I was on the fence about front vs rear installation for various reasons. In the end I chose the front and could not be happier. With the bose radio and no sat (05 MO) this install was really simple. I used a 2" plastic putty knife to pry the corners of the vent cover up and slide a regular flat head in the space and popped off the vent covers no problem. Removed the 2 top screws and the black plastic on the bottom of the radio head pops off when you squeeze it to get to the other 2 screws holding the radio head in place. Once those two are done the head can be pulled forward and you are ready to go. I had to remove only one wire on the back. People had a hard time with this but luckily I had an ink pen in the car and used the tip of it to depress the little clips and the plug came right out. I attached the harness and I popped off the side panel next to the drivers side gas pedal(pic attached) and grounded it there. The Ipod adapter box I attached to the top of the radio(Brian AKA Jerseyparts had to tell me that little trick on the phone) head and mounted the box to the rear of the radio head so it can fully slide back into place. I had to go get some scotch double sided tape form Home Depot (**Brian this would be a nice addition to the kit**). I then put it back together. I decided to forego putting the IPOD in the glove box and am just using the storage area beneth the radio and I turn the rubber mat upside down over top of it and you can not see anything at all, the wire can be slide directly behind this area easily(I originally had it coming out of the side by the glove box). I may try to run it to the center are storage console but for now I like this and will see how it goes. This install was truly easy and took me about 1/2 hour of actual work. Another 1/2 hour of figuring out where to put things but now you know you have some more options that will hopefully buy you some time. There are some short comings with the manipulation of the IPod but all in all I am very happy. Again thanks to everyone that posted info out here |
|
|
| gem_tim |
| Sorry gang did not know how to post multiple pics, here is te location of the IPOD from my earlier post |
|
|
| vicky3269 |
Hi everyone. I am new here. I have an 06 Murano with the Bose 6 disc changer and no satellite. I really want to get the Ipod interface, but not sure if my old Ipod mini will even work, as I have heard older Ipods don't work.
Also, my husband and I are not good at this stuff at all, will Nissan install this for us, or is there anyone in the SF Bay Area that would be willing to install this in our Murano for a decent price?
Thanks,
Vicky :) |
|
|
| OurMO |
quote:
Originally posted by vicky3269
Hi everyone. I am new here. I have an 06 Murano with the Bose 6 disc changer and no satellite. I really want to get the Ipod interface, but not sure if my old Ipod mini will even work, as I have heard older Ipods don't work.
Also, my husband and I are not good at this stuff at all, will Nissan install this for us, or is there anyone in the SF Bay Area that would be willing to install this in our Murano for a decent price?
Thanks,
Vicky :)
Vicky, I can confirm that the ipod mini will work. That is what I use in my 03.
Cheers,
Dan |
|
|
| rixmo |
| Vicky, get the kit that plugs in the rear then. All you have to do is find the wiring harness behind the rear seat (this thread has pictures of it) and plug the cables into it. You can hook up your IPOD to sit in the rear trunk area and not have to worry about pulling cables through your whole car. It truly is one of the easiest modifications you can do.:2: |
|
|
| vicky3269 |
Thanks so much for the replies! I think I will go ahead and order it!
Vicky:) |
|
|
| ritchwell |
not sure if this was ask before im hoping jerseyparts can answer the question. since this topic is for ipod intergration, my question is since some of the ipods have video player. im wondering will they be able to develope or have something that will be able to play the video of the ipod player to the Murano colored screen. Thanks
ritch |
|
|
| jlaudio |
| If you can add a RCA solution to the screen of the Murano you can just buy the cable for plugging into the headphone out and play video and sound that way. I use the cable on my tv with my old 30 gig video all the time. The cable is cheap and can be found at walmart for as much as $15. |
|
|
| jerseyparts |
At this time we have nothing that can accomplish this, but there is a guy on an Infiniti forum who has designed a cable just for this.
the website is www.infinitifx.org
Brian |
|
|
| zebelkhan |
quote:
Originally posted by jlaudio
If you can add a RCA solution to the screen of the Murano you can just buy the cable for plugging into the headphone out and play video and sound that way. I use the cable on my tv with my old 30 gig video all the time. The cable is cheap and can be found at walmart for as much as $15.
I think the IPOD integration kit also gives you the ability to control your IPOD through the radio controls. |
|
|
| TazzyTazzy |
I have an 06 murano SL, no Sat installed.
I take it i have to order iPod Adaptor (#999U7-VR002) and the Harness (#999U7-VS000).
Does this have AUX in as I would also like the ability to use my Sirius Sportster using the car adapter (external antenna, power, etc) but using a direct audio feed in stead of FM.
If this are not the right parts, what parts do I need to allow me to use either the iPod or my Sirius Sportster?
Thank you. |
|
|
| big_daddy_mpd |
quote:
Originally posted by gfb107
And finally the ipod kit installed in the space covered by that carpeted panel:
gfb107...of all of the "installs" yours is just the plain most "elegant". :2: I LOVE elegance (I'm a systems architect...we architects LOVE elegant solutions...and frankly, yours is the best. Now, here's the question...did you "drill" a hole to get the ipod cable up into the console? Was there a natural pass through up through the console to pass it up through? I too have a 2006 SL AWD, with the nice "split cover" upper tray console section. I'd like to hide my ipod there, when in motion, easy access to take with. Any more details on how you got the cable to the top console tray. I just bought the same cable/unit from JerseyParts. Again...I'm assuming you used a coat hanger/wire snake, to pull the harness from behind the back seat, under the carpet, to the front console shown here. More details please (I'm seriously NOT a hardware guy...software is my ballywick!)
Regards,
Big |
|
|
| big_daddy_mpd |
Got the box and harness plugged in, ran it to the middle console, plugged in the iPod, and Oh, My! Brian...you're right, the sound is just astounding, even my wife commented on how good it was. My car stereo is complete now (and my black 30GB video ipod, goes great with my black leather interior!) Anyway, the only caution I can give you folks, is if you mount the box under the middle console, mount it as far back as you can, and still get some solid surface to stick it too...the cable to the ipod sticks out about 2 inches, and you won't get the carpet/plastic panel replaced if you don't.
Regards,
Big |
|
|
| dylanursula |
All,
I have read this thread and am still confused as to what parts I need. I have a 05 Murano SL with no sat, no cd changer and standard Nissan radio (no BOSE). I would like to add an IPOD that plugs into the glove box or console in the front. What parts do I need and whats the easiet way to install.
Thanks |
|
|
| kitesurf |
2006 No SAT install this past weekend thanks to Brian, PappaBacon, and all that posted helpful hints on this forum.
It took me less than two hours for the front dash install. The most difficult part (1 hour) was trying to figure out where I wanted to run the cord and put the Ipod. I ended up running the cord to the back of the glovebox and leaving the Ipod in there. Out of sight of prying eyes. The front install gives you many options - I highly suggest trying that vs. going behind the rear seat and running the cord up to the middle counsel.
The sound is incredible. No more FM modulator hiss. |
|
|
| jerseyparts |
quote:
Originally posted by kitesurf
2006 No SAT install this past weekend thanks to Brian, PappaBacon, and all that posted helpful hints on this forum.
It took me less than two hours for the front dash install. The most difficult part (1 hour) was trying to figure out where I wanted to run the cord and put the Ipod. I ended up running the cord to the back of the glovebox and leaving the Ipod in there. Out of sight of prying eyes. The front install gives you many options - I highly suggest trying that vs. going behind the rear seat and running the cord up to the middle counsel.
The sound is incredible. No more FM modulator hiss.
Glad to hear it all worked out for you.
The fun part is trying to figure out the controls at first, but you get the hang of it pretty fast!
To the Post above this one, get the Front Install Package without Sat at the www.NissanIpod.com site, it will have everything you need.
As far as the installation, there are multiple way of installing it, it all depends on where you want your Ipod to wind up.
Brian |
|
|
| adubya |
I have an '06 Murano SL AWD with Navigation but no Sat.
I instructed the dealer to try the Titan '06 Ipod kit and they got it but when they tried to install it they said there was nothing to hook it up to.
They called back to Nissan USA and were told (of course) that there's no way to hook up the iPod to the Murano. Of course I found that ludicrous because of everything I've read here.
I asked if it needed to get the Satellite wiring installed first and they said no, it wouldn't matter.
I'm assuming that they're clueless, even more so than I am and that's saying something.
Can anyone tell me what I'm supposed to get an how to install it?
Thanks! |
|
|
| rixmo |
| Plug the Titan kit into the back under the cardboard flap behind the right rear seat. Check there to see if you have a white unused connection (for Satellite). That's what the Titan kit plugs into. The dash kit that Jersey Parts sells plugs into the back of the radio in place of the satellite harness. |
|
|
| jerseyparts |
| Correct, if you have the Titan Kit, simply find the satellite harness in the rear of the vehicle, and that is where that kit will plug into.... |
|
|
| bmw911driver |
Hello Jerseyparts. I bought an iPod adatpter for my 2007 Murano and I love it.
Did you see the pictures of the iPod integration in the 2009 Murano on the Nissan USA website?
http://www.nissanusa.com/09murano/i...omepage.Home.P2
I think they did a great job! I like the split screen and the songs listed on the right section of the screen. |
|
|
| jerseyparts |
quote:
Originally posted by bmw911driver
Hello Jerseyparts. I bought an iPod adatpter for my 2007 Murano and I love it.
Did you see the pictures of the iPod integration in the 2009 Murano on the Nissan USA website?
http://www.nissanusa.com/09murano/i...omepage.Home.P2
I think they did a great job! I like the split screen and the songs listed on the right section of the screen.
Yea I seen it, it will be cool. The Hard drive on voard and then you can add the ipod adapter.
I am just waiting for the new kits to become available from Nissan so I can check em out myself....
Brian |
|
|
| bmw911driver |
I'm not crazy about the Compact Flash slot (What is the maximum CF capacity and how do you navigate if at all?, maybe for the occasional music file? I guess the harddrive stores the ripped CD's instead of a 6 CD mp3 player?
iPod integration and song selection with steering wheel buttons is still the best thing for larger music collections I guess. |
|
|
| biggun |
quote:
Originally posted by bmw911driver
I'm not crazy about the Compact Flash slot (What is the maximum CF capacity and how do you navigate if at all?, maybe for the occasional music file? I guess the harddrive stores the ripped CD's instead of a 6 CD mp3 player?
iPod integration and song selection with steering wheel buttons is still the best thing for larger music collections I guess.
At first, I thought the same thing. I mean how many devices really use compact flash these days. More devices are switching to smaller formats like the SD, mini SD, and now micro SD media or similar (AKA Sony media).
But then it dawned on me - most, if not all of those media can be adapted to the compact flash drive with inexpensive adapters. That would not be the case for the compact flash if a smaller slot was provided.
So, I guess Nissan thought about it. However, I still thing that a USB slot would have been the best universal port to have. |
|
|
| bmw911driver |
| In my case I might simply copy music from my iTunes library for my wife on a 1GB CF card and there she goes... while I'd be using the iPod with the adapter. |
|
|
| Onarum |
I just installed the iPod adapter kit (from NissanIpod.com) in my 2007 SL AWD. It took almost 3 hours all told. I did it a couple of days after I installed the XM satellite radio. I took a bunch of pictures and will post them one of these days.
While the adapter installation wasn't rocket science, it was time consuming and definitely not for the weak of heart. Once you get the head unit pulled out, you'll know what I mean.
Removing the head unit was straightforward, as was plugging in the adapter and the harnesses. But figuring out where to put the adpater took a bit of time. I ended up wrapping it in bubble wrap and foam padding, then stuffing it just below and to the right of the head unit. There just wasn't anywhere else I could find to put it that the harnesses would reach. It's wedged in and won't be moving anywhere. 2 harness wires plug in to the back of the adapter, and one of them was too short.
I opted for the glove box installation. Running the wire through the back of the glove box was easy. The kit comes with a rubber grommet that makes it all look nice and neat. Just drill a hole in the back of the glove box, poke the wire through the grommet, then push the grommet into the hole. The big problem was getting the glove box back in. There's a little lanyard that controls the opening of the glove box, and it was quite a juggling act to reattach it. The lanyard is very short and the space to get the screwdriver in is very small. You really need to have a short phillips head screwdriver, no longer than 3 inches.
Despite all the problems, it's in, and it works. |
|
|
|
