Nissan Murano Forum

Nissan Murano Forum (https://www.nissanmurano.org/forums/)
-   1st Gen (2003-2007) (https://www.nissanmurano.org/forums/82-1st-gen-2003-2007/)
-   -   Harness connector to Camshaft Position Sensor (https://www.nissanmurano.org/forums/82-1st-gen-2003-2007/222718-harness-connector-camshaft-position-sensor.html)

CanCar 05-15-2019 05:35 PM

Harness connector to Camshaft Position Sensor
 
2 Attachment(s)
I have been trying buy I cannot disconnect the harness connector to the camshaft position sensor (CPS). I am getting a P0340 and just want to ensure the connection is still good on my 2004 SE.
Car runs smoothly, starts up ok. but there has been a few occasions in the last 3 weeks when the engines just stops while I am driving. Engine restarts itself while the car is still moving when it cuts out by me pushing the gas pedal all the way down... If stalls out when I am idling, the only way it starts up again is "flooring" the gas pedal then turn the key. It starts up roughly but once it gets going it runs fine until the next time it stalls.
P0340 code is for bank A, harder to get to than the CPS on bank B, thats why I am trying to "learn" how to disconnect B first, the easier to access one, before disconnecting the bank A CPS.


Anyways, anyone know how to disconnect it? I want to ask before I break something.


Recently did both front hubs, changed belts and replaced Power steering high pressure hose. Worried that I might have damaged something while working oh the high pressure hose between the engine and the firewall... thus causing the stalls.

I need coffee 05-15-2019 05:52 PM

Quote:

Originally Posted by CanCar (Post 740798)
I have been trying buy I cannot disconnect the harness connector to the camshaft position sensor (CPS). I am getting a P0340 and just want to ensure the connection is still good on my 2004 SE.
Car runs smoothly, starts up ok. but there has been a few occasions in the last 3 weeks when the engines just stops while I am driving. Engine restarts itself while the car is still moving when it cuts out by me pushing the gas pedal all the way down... If stalls out when I am idling, the only way it starts up again is "flooring" the gas pedal then turn the key. It starts up roughly but once it gets going it runs fine until the next time it stalls.
P0340 code is for bank A, harder to get to than the CPS on bank B, thats why I am trying to "learn" how to disconnect B first, the easier to access one, before disconnecting the bank A CPS.

Anyways, anyone know how to disconnect it? I want to ask before I break something.

Recently did both front hubs, changed belts and replaced Power steering high pressure hose. Worried that I might have damaged something while working oh the high pressure hose between the engine and the firewall... thus causing the stalls.

Do you see that lime-green colored piece of plastic on the connector? You don't pinch it like most other locking connectors--you literally have to push that plastic piece down into the connector and that will release the lock and then you can pull the connector off.

Fletcher Beard 05-18-2019 06:45 PM

You may have to use a screwdriver to move it like i did when i did mine recently. The A sensor was stuck and needed a bit of a puch from something harder than a fingernail.

DreamCar5683 05-21-2019 11:41 AM

25 Attachment(s)
Quote:

Originally Posted by CanCar (Post 740798)
I have been trying buy I cannot disconnect the harness connector to the camshaft position sensor (CPS). I am getting a P0340 and just want to ensure the connection is still good on my 2004 SE.
Car runs smoothly, starts up ok. but there has been a few occasions in the last 3 weeks when the engines just stops while I am driving. Engine restarts itself while the car is still moving when it cuts out by me pushing the gas pedal all the way down... If stalls out when I am idling, the only way it starts up again is "flooring" the gas pedal then turn the key. It starts up roughly but once it gets going it runs fine until the next time it stalls.
P0340 code is for bank A, harder to get to than the CPS on bank B, thats why I am trying to "learn" how to disconnect B first, the easier to access one, before disconnecting the bank A CPS.


Anyways, anyone know how to disconnect it? I want to ask before I break something.


Recently did both front hubs, changed belts and replaced Power steering high pressure hose. Worried that I might have damaged something while working oh the high pressure hose between the engine and the firewall... thus causing the stalls.

My video on this project covers this:

https://youtu.be/A6nPeRl_510


All times are GMT -4. The time now is 07:35 AM.

Powered by vBulletin® Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.

User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.

 
For the best viewing experience please update your browser to Google Chrome