Nissan Murano Forum banner

1 - 6 of 6 Posts

·
Registered
Joined
·
63 Posts
Discussion Starter #1
Hey everyone,
I know this might be a repeated thread, but I honestly couuldn't find it in the forums. So I apologize in advance if it does exist. I am looking for the Key Fob programming Instructions for a 2004 Murano SL AWD. I bought a blank key fob from ebay, and I need the instructions on programming.
Thanks in Advance
 

·
Registered
Joined
·
982 Posts
REPROGRAM KEY FOB

I hope this is helpful information....


Nissan Vehicles

The horn chirp can be disable by pressing the lock and unlock buttons simultaneously until the hazard lights flash, and no enable press the lock and unlock until the horn chirp.
To reprogram (enter new ID) key fob (keyless remote controller) follow the steps.

1. Close all doors and lock all doors
2. Insert and remove the key from the ignition key cylinder more than six times within 10 seconds.
(The hazard warning lamp will then flash.)
NOTE: Key should be withdrawn from ignition key cylinder completely each time.
NOTE: Do not rush the insertion/removal key cycling process. The side marker/tail/license lamps and interior illumination will flash twice when this step is accurately completed.
3. Insert key on ignition key cylinder and turn ignition key switch to "AAC" position
At this time, the new ID code is entered and original (previous) ID codes are erase.
4. Press any button on the new remote controller once. (The hazard warning lamp will then flash)
NOTE:
Do not press the button more than one time in the above step. If the button
is pressed more than one time, the programming procedure will not be successful.
The side marker/tail/license lamps and interior illumination will flash twice when this
step is accurately completed and programming is successful.
If there is only one remote controller skip step 5.
5. Additional ID code entry
Release the door lock, then lock again with door lock/unlock switch
(In power window main switch)
6. Remove key from ignition
7. Unlock driver side door, open driver side door and then close the door. (END)
NOTE:
If you need to activate more than two additional new remote controllers, repeat
the procedure on step 5 "Additional ID code entry" for each new remote controller.
NOTE:
Entry of maximum four ID codes is allowed and any attempt to enter more will be ignore.



Did not work? Try these steps

To reprogram (enter new ID) key fob (keyless remote controller) follow the steps.
1. Close all doors and lock all doors
2. From the door switch unlock the trunk.
3. Insert and remove the key from the ignition key cylinder six times within 10 seconds.
NOTE:
Key should be withdrawn from ignition key cylinder completely each time.
NOTE:
Do not rush the insertion/removal key cycling process. The side
marker/tail/license lamps and interior illumination will flash twice when this step is
accurately completed.
NOTE:
At this time, the new ID code is entered and original (previous) ID codes are erase.
4. Manually unlock and lock the driver side door
5. Push any button on the new remote controller once.
If there is only one remote controller skip step 6.
6. Additional ID code entry
Repeat step 4 and 5
7. END.
NOTE:
If you need to activate more than two additional new remote controllers, repeat
the procedure on step 6 "Additional ID code entry" for each new remote controller.
NOTE:
Entry of maximum four ID codes is allowed and any attempt to enter more will be ignore.
-Did not work? Try these steps
ID CODE ENTRY PRODCEDURE
Step 1) Sit in drivers seat, close and lock all doors.
Step 2) Insert key into and remove it from ignition key cylinder more than six times within 10 seconds.
(Hazard warning lamps will then flash twice).

NOTE:
Withdraw key completely from ignition key cylinder each time.
If procedure is performed too fast, system will not enter registration mode.
Step 3) Insert key into ignition key cylinder and turn to ACC position.
Step 4) Push any button on remote controller once. (Hazard warning lamps will then flash twice).
At this time, the oldest ID code is erased and the new ID code is entered.
Step 5) Do you want to enter any additional remote controller ID codes?
A maximum of four ID codes may be entered. If more then four ID codes are entered,
the oldest ID code will be erased.
If you do not want to enter any additional remote controller ID codes, go to Step 9).
Step 6) ADDITIONAL ID CODE ENTRY
Lock all doors with LH (driver side) lock/unlock switch
(in main power window and door lock/unlock switch).
Step 7) Push any button twice on remote controller once, (Hazard warning lamps will then flash twice).
At this time, the oldest ID code is erased and the new ID code is entered.
Step 8) Do you want to enter any additional remote controller ID codes?
If so, unlock doors then repeat Step 6) and Step 7).
Step 9) When complete, open door, and check operation of remote.
 

·
Registered
Joined
·
12,512 Posts
And for that they charge $100?!

You would think they would do it as a courtesy after having spent over 30 grand.

-njjoe
 

·
Premium Member
Joined
·
7,136 Posts
njjoe said:
And for that they charge $100?!

You would think they would do it as a courtesy after having spent over 30 grand.

-njjoe
If done properly, the whole programming takes less than 30 seconds per fob!
 

·
Registered
Joined
·
12,512 Posts
About 5 years ago one of the key fobs for my Jeep GC failed. I went to the dealership and bought a new one. As I was about to leave, the guy behind the parts counter told me to pull my car around to the side and he would take care of it. "Take care of what?" I asked. He then spent all of one minute to program my key fob.

That, to me, was an example of good customer service.

It is outrageous that Nissan would even consider charging us to program the fob, even if the fob was purchased elsewhere.

-njjoe
 
1 - 6 of 6 Posts
Top