Anyone know if the shade on the moonroof so can be adjusted to close more as I have a slight gap when fully closed with sun light shinning through. Is there an adjustment screw or something? I really do not want to take it to the dealer to have that done.
Panorama Roof Shade adjustment?
zzyzx
1 - 5 of 5 Posts
Anyone know if the shade on the moonroof so can be adjusted to close more as I have a slight gap when fully closed with sun light shinning through. Is there an adjustment screw or something? I really do not want to take it to the dealer to have that done.
Joined
·
1,012 Posts
MEMORY RESET PROCEDURE
1. Please observe the following instructions while confirming the sunroof operation.
NOTE:
Do not disconnect the electronic power while the sunroof is operating or within 5 seconds after the sunroof
stops. (to wipe-out the memory of lid position and operating friction.)
2. Initialization of system should be conducted after the following conditions.
When the battery is out or connector is disconnected while sunroof is operating or within 5 seconds
after sunroof stops.
When the sunroof motor is changed.
When an emergency handle is used.
When the sunroof does not operate normally. (Incomplete initialization conditions)
INITIALIZATION PROCEDURE
If the sunroof does not close or open automatically, use the following procedure to return sunroof operation to
normal.
1. Push the TILT UP switch and start the tilt up operation.
2. Release the TILT UP switch once, press the TILT UP switch again. Keep pushing the switch until tilt lid
pops up.
3. The glass lid will move toward tilt up direction and will be stopped mechanically, and then it will be automatically
fully closed. (Keep pushing the switch during this operation)
4. Release the switch again, and push the TILT UP switch within the first 10 seconds. (Keep pushing the
switch)
5. After 4 seconds, the class lid will be automatically operated in sequence of �gslide open�h �¨�gslide
close�h�¨�gtilt up�h�¨�gtilt down�h.
6. After the glass lid stops, release the switch after 0.5 seconds. (Keep pressing the switch during this operation)
7. If PRE-SELECTED switch operates normally, this initialization is done.
1. Please observe the following instructions while confirming the sunroof operation.
NOTE:
Do not disconnect the electronic power while the sunroof is operating or within 5 seconds after the sunroof
stops. (to wipe-out the memory of lid position and operating friction.)
2. Initialization of system should be conducted after the following conditions.
When the battery is out or connector is disconnected while sunroof is operating or within 5 seconds
after sunroof stops.
When the sunroof motor is changed.
When an emergency handle is used.
When the sunroof does not operate normally. (Incomplete initialization conditions)
INITIALIZATION PROCEDURE
If the sunroof does not close or open automatically, use the following procedure to return sunroof operation to
normal.
1. Push the TILT UP switch and start the tilt up operation.
2. Release the TILT UP switch once, press the TILT UP switch again. Keep pushing the switch until tilt lid
pops up.
3. The glass lid will move toward tilt up direction and will be stopped mechanically, and then it will be automatically
fully closed. (Keep pushing the switch during this operation)
4. Release the switch again, and push the TILT UP switch within the first 10 seconds. (Keep pushing the
switch)
5. After 4 seconds, the class lid will be automatically operated in sequence of �gslide open�h �¨�gslide
close�h�¨�gtilt up�h�¨�gtilt down�h.
6. After the glass lid stops, release the switch after 0.5 seconds. (Keep pressing the switch during this operation)
7. If PRE-SELECTED switch operates normally, this initialization is done.
Joined
·
1,012 Posts
Try:
INITIALIZATION PROCEDURE
If the sunroof or sunshade does not close or open automatically, use the following procedure to return sunroof
or sunshade operation to normal.
1. Close the sunroof and sunshade, then release the sunroof switch once.
2. Press and hold the sunroof switch CLOSE (1st or 2nd) again (for approx. 10 seconds), then sunroof will
move to forward and it will be stopped mechanically.
3. Release the sunroof switch, and press and hold the sunroof switch CLOSE (1st or 2nd) again. then sunroof
and sunshade will automatically move to fully closed⇒fully open⇒fully closed.
4. Release sunroof switch, after the sunroof is fully closed.
INITIALIZATION PROCEDURE
If the sunroof or sunshade does not close or open automatically, use the following procedure to return sunroof
or sunshade operation to normal.
1. Close the sunroof and sunshade, then release the sunroof switch once.
2. Press and hold the sunroof switch CLOSE (1st or 2nd) again (for approx. 10 seconds), then sunroof will
move to forward and it will be stopped mechanically.
3. Release the sunroof switch, and press and hold the sunroof switch CLOSE (1st or 2nd) again. then sunroof
and sunshade will automatically move to fully closed⇒fully open⇒fully closed.
4. Release sunroof switch, after the sunroof is fully closed.
Joined
·
1 Posts
thanks,this procedure work in my wife truck
1 - 5 of 5 Posts
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
