[Scrib]

OK, here is the newjack photo reprint from page 16.
Check out the area with the white business card.
I started to spray the grease at the top where the card is shown in the photo below. I continued spraying the grease and went down the door about 15 inches. I did not remove any parts. I first coated a business card with the grease and slid it up and down but figured it was not enough. I then, like JimC just shot the stuff into the groove and wiped the excess. The whole thing took 2 minutes. Scrib, does this post help?
Bob1

OK, cool. I see what you did. It was a CRAZY day at work. Wasn't thinking things through. I clearly see what's going on.

Do you think there's a way to hide the card; i.e. is it necessary to have that much exposed? I wonder if by separating things but HIDING the card or whatver.... It'd look better, but still function the same.

Unfortunately, I still have about 3 hours of work to complete this evening. I'll tackle this tomorrow or Wednesday.

Thanks!

 

[GripperDon]

Slide it down further and use a black paper.

 

[Scrib]

Slide it down further and use a black paper.

And if you have Caffe Latte interior???

Ok, I'll stop. :2:

 

[GripperDon]

Use a Starbuck's cup torn and folded.

 

[bob1]

Scrib, I first tried the card by itself as indicated in that photo.
My tic noise changed to a moan and a groan. That is the point when I sprayed the card and slid it up and down just to get the goop in the offending area. I removed the card and let the lube due it's thing. I have no card in that slot just the lithium.
That's about it.
Bob1

 

[Gonzo]

Gonzo You are testing me.

Whacha talkn' about?

 

[GripperDon]

That was me and thus far its been quiet. I used a over sized piece of foam and pushed it in with my credit card. I would have use something like you suggested but I was affraid that it would prematurally stick prior to my desired insertion point. (OK no funny jokes about that one please....)

No jokes hard to pass up!

 

[9231]

Scrib - Like Bob, I don't have the card in position either, just the WLG sprayed into the crack on the passenger side door. On the driver's side door of my Murano, I used a light color felt instead of a business card (its the stuff you find at Home Depot for sticking onto the bottoms of chair and table legs so that you can slide the furniture along wood floors smoothly - felt on one side, sticky on the other). For the driver's door, the felt/business card trick worked. It didn't on the passenger side. I was at a loss until Bob's suggestion, hence the WLG solution. If the felt stops working on the driver's side, I'm switching to the WLG. I don't notice the felt because its colored similar to the Cafe Latte interior plastic and you don't see that part of the trim with the door closed.

 

[Scrib]

Thanks all. I'll take a look in the next day or two and see what I can find.

:29:

 

[Gonzo]

Aren't you guys nervous about spraying lub in the door... long term effects of dirt attraction to moving parts?

 

[9231]

Not really. There aren't too many moving parts exposed on that section of door (right at the edge) and the whole affair is sealed up pretty well. I can't see much dirt getting in there. When I took the door panels off my last car to change out the power window motor, the inside of the doors looked as new and clean as the day I bought it - and that was eight years before! So I don't think it should be an issue.

 

[simplesb]

Ok cross your fiingers I will supposedly have a new door panel installed this week. Because of the could temperatures here the rattling has been constant so I'm hoping I see , or this case hear, a noticable difference.

 

[Scrib]

Scrib - Like Bob, I don't have the card in position either, just the WLG sprayed into the crack on the passenger side door. On the driver's side door of my Murano, I used a light color felt instead of a business card (its the stuff you find at Home Depot for sticking onto the bottoms of chair and table legs so that you can slide the furniture along wood floors smoothly - felt on one side, sticky on the other). For the driver's door, the felt/business card trick worked. It didn't on the passenger side. I was at a loss until Bob's suggestion, hence the WLG solution. If the felt stops working on the driver's side, I'm switching to the WLG. I don't notice the felt because its colored similar to the Cafe Latte interior plastic and you don't see that part of the trim with the door closed.

Well, it worked!!! :2:

Took the MO for a 30 mile drive yesterday (wife dragged me around shopping :O ), and I didn't hear a peep.

So that's two rattles I've fixed... But I'm now happy to say our MO is dead quiet now.

 

[JMcDonald]

Just pitching in to confirm that the WLG spray seems to have done the trick with eliminating the ticks in both the driver and passenger sides...it's been 1 week and no irritating noises...

 

[lapriester]

Well, I'm a new Murano owner and definately new to the forum (yesterday) but, I have a couple of ideas on the door rattle problem. I've noticed that, in some cases, folks are curing the ticks by sliding a card or thin cardboard between the panel and the metal of the door. I had the same problem in cold weather in my Ford pickup and my Lebaron convertable. The plastic door panel, after about 3 months of ownership and the first time it got cold, began making a creaking and ticking sound on rough roads and on turns. I solved that problem by looking closely at every place the panel came in direct contact with the door metal. Once I ID'd those places I pried open those locations and put thin, double stick (white) foam tape between the panel and the door metal and trimmed off the excess. ALL the noises went away. 80K later on my truck and 50K later on the car I had to replace the foam tape because it finaly wore through and started ticking again. Sure solved the problem on those vehicles, might work for some of the MO's that have noise related to plastic/metal contact.

Larry :2:

 

[GripperDon]

NICE JOB LARRY

 

[estoyer]

WINDOW RATTLE

Well here we go again.... I talked with the service tec and showed him the tsp I printed out and he only replaced the both front doors window gaskets. Now the ticking noise is comming from the back windows. Next oil change I'll let them know then maybe I'll get all of the ticking noises out.......... Replacing the front gaskets took care of the ticking in the front.

 

[GripperDon]

Make sure you tell them "BOTH" back windows!!!!

 

[bob1]

High five to everyone solving their window tic noise!!!!
Glad the fix is working and just praying that it is a lasting fix.
Bob1
':2:'

 

[ADV]

Try using some single-side-adhesive black felt instead of the foam. Should not wear nearly a quickly. Foam isn't very resistant to friction. All automakers use felt tape between certain plastic parts for just this purpose. In the MO they seem to have forgotten...

Well, I'm a new Murano owner and definately new to the forum (yesterday) but, I have a couple of ideas on the door rattle problem. I've noticed that, in some cases, folks are curing the ticks by sliding a card or thin cardboard between the panel and the metal of the door. I had the same problem in cold weather in my Ford pickup and my Lebaron convertable. The plastic door panel, after about 3 months of ownership and the first time it got cold, began making a creaking and ticking sound on rough roads and on turns. I solved that problem by looking closely at every place the panel came in direct contact with the door metal. Once I ID'd those places I pried open those locations and put thin, double stick (white) foam tape between the panel and the door metal and trimmed off the excess. ALL the noises went away. 80K later on my truck and 50K later on the car I had to replace the foam tape because it finaly wore through and started ticking again. Sure solved the problem on those vehicles, might work for some of the MO's that have noise related to plastic/metal contact.

Larry :2: